What method is used for coating inspection on the feeding section?

Jinan LIJIANG Glass generally uses contact-type detection of Low-E glass film. The measurement point of the coating test is the measurement point of the round head, rather than the measurement point of other manufacturers using the needle. Therefore, the Low-E glass will not be cut during the detection process. The photoelectric sensing type used by other manufacturers to detect Low-E coating is easy to fail to notice if the Low-E glass coating is shallow.

How many pairs of brushes and rubber rollers are there in the washing section of Jinan LIJIANG Glass IG line?

The washing section of the Jinan LIJIANG Glass insulating glass production line is generally equipped with three pairs of brushes and four pairs of rubber rollers. However, if customers have special requirements for glass cleaning and drying, Jinan LIJIANG Glass can choose various brush and rubber roller matching methods to ensure customer satisfaction.
In addition, the brushes used in the cleaning section are all soft brushes with a diameter of 0.1mm, which can clean offline Low-E glass. The cleaning sections of other manufacturers generally use hard-bristled brushes, and the effect of hard-bristled meetings on Low-E glass is usually poor.

Can the air knife in the drying section of the Jinan LIJIANG Glass IG line be movable? What are the characteristics of glue compared with other manufacturers?

The air knife in the drying section of the Jinan LIJIANG Glass insulating glass production line can automatically adjust the width of the glass according to the thickness of the glass. It can be suitable for washing and drying glass of different thicknesses, and the air-drying speed is significantly improved. Other manufacturers generally use fixed air knives in the drying section. The speed of washing and drying different thicknesses of glass will slow down, which is not suitable for flexible production in complex glass processing environments.

How is the drying section of the Jinan LIJIANG Glass IG line generally driven?

The drying section of the Jinan LIJIANG Glass insulating glass production line generally uses front and rear squeeze wheels to drive, and the front and rear wheels are powered. Other manufacturers use supporting wheels to operate, and some have forced wheels in the front and steering wheels in the back. Compared with other manufacturers, Jinan LIJIANG Glass has more advantages. Jinan LIJIANG Glass adopts this method to operate, and both large and small glass can pass smoothly. In the transmission method of other manufacturers in the drying section, the small type of glass will turn over, and the large variety of glass will not moving. Conducive to the production operations of glass deep-processing industry.

How powerful is the fan used in the drying section of the Jinan LIJIANG Glass IG line? What are the advantages?

The power of the fan in the drying section of the Jinan LIJIANG Glass 2m insulating glass production line is 15kw, the power of the fan in the drying section of the 2.5m insulating glass production line is 18.5kw, and the noise of the fan is about 80 decibels; and the fan has a damper, which can be used when it is not working. The automatic closing of the air door can ensure that the glass is still very clean when the washing section is suspended.

What is the structure of the inflatable plate pressing section of the Jinan LIJIANG Glass IG line? What are the advantages?

Jinan LIJIANG Glass insulating glass production line inflatable plate pressing section, inflatable beam, and transmission part adopt a synchronous belt structure, which is integrated. This structure has better sealing performance and will not easily cause air leakage at the bottom of the insulating glass; In contrast, other manufacturers’ pressure sections of the inflatable plate, the inflatable beam, and the transfer wheel structure are separated so that the air leakage will occur at the bottom of the hollow glass during processing.

In the production of three-glass and two-cavity insulating glass, does the Jinan LIJIANG Glass automatic sealing robot machine use one-time sealing or two-time sealing?

When Jinan LIJIANG Glass automatic insulating glass sealing robot machine produces three-glass and two-cavity insulating glass, it can be sealed once or twice. In the production and processing of three-glass and two-cavity insulating glass, the placement requirements of the aluminum strips for insulating glass processing are higher, and the dimensional accuracy of the insulating glass aluminum strips is required to be higher. Generally speaking, the sealing effect of secondary sealing will be better, but the speed will also slow down, which will affect the processing efficiency.

In the production of three-glass and two-cavity insulating glass, does the Jinan LIJIANG Glass automatic sealing robot machine use one-time sealing or two-time sealing?

When Jinan LIJIANG Glass automatic insulating glass sealing robot machine produces three-glass and two-cavity insulating glass, it can be sealed once or twice. In the production and processing of three-glass and two-cavity insulating glass, the placement requirements of the aluminum strips for insulating glass processing are higher, and the dimensional accuracy of the insulating glass aluminum strips is required to be higher. Generally speaking, the sealing effect of secondary sealing will be better, but the speed will also slow down, which will affect the processing efficiency.

What are the advantages of Jinan LIJIANG Glass Auotmatic Low-E Glass Edge Deleting Machine?

Jinan LIJIANG Glass Auotmatic Low-E Glass Edge Deleting Machine can be connected to the entire insulating glass production line, eliminating the need for the manual film removal process, the film removal effect is good, the glass processing flatness is better, mainly for the tempered Low-E glass film removal, can be used Large-format Low-E glass is removed.
In addition, some practitioners in the glass deep processing industry use manual film removal to remove Low-E glass. This manual removal has a poor effect and a slower speed. It can only deduct the film on the glass before tempering. The heating time of white glass and Low-E glass is different during tempering, which will cause the glass to be deformed, and the glass will not be so flat.